Input Voltage:	Specified: 90 - 264Vac, (85 - 264Vac with derating) Nameplate: 100 - 240Vac
Input Frequency:	Specified: 47 - 63Hz Nameplate: 50 - 60Hz
No Load Input Power:	< 1.5W @ 115V/230V
Inrush Current:	60A max @ 264Vac
Power Factor:	>0.95 @ 115Vac, >0.95 @ 230Vac, full load

Main Output

Output Power:	520W (linearly derated to 480W @ 85Vac) [natural convection, open U-frame version] 800W (linearly derated to 720W @ 85Vac) [forced air cooling, enclosed version]
Constant Current Operation:	CC/CV with a brick-wall CC limit at ~115% nominal current rating. Power supply enters auto-recovery (hiccup) mode once Vout drops to ~75% of nominal value.
Turn-on Delay:	< 2 seconds @ 85Vac (full load)
Voltage Set-Point Tolerance:	± 2.0% (measured at connector, no load, Ta = -20 to 50°C)
Load Regulation:	± 1.0% (measured at connector)
Line Regulation:	± 0.5% (measured at connector)
Ripple:	1% pk-pk (using a 47µF low-ESR cap + 0.1µF ceramic capacitor, measured @ 20MHz BW)
Transient Response:	<5% deviation (with 25-75% load step), recovery to within 1% in 1ms
Startup Overshoot:	<5% (full load)
Hold-up Time:	20ms min. (full load)

Standby Output

Output Voltage:	5V
Output Current:	1A
Line/Load Regulation + Set-Point Tolerance:	± 4%
Ripple:	1% pk-pk (using a 47µF low-ESR cap + 0.1µF ceramic capacitor, measured @ 20MHz BW)
Always on?	Yes

Output Voltage:	12V
Output Current:	0.6A
Line/Load Regulation + Set-Point Tolerance:	± 4%
Always on?	On or off depending on internal sensed temperature

Remote On/Off (EN)	Yes
Remote Voltage Sense:	Yes, voltage drop compensation up to 500mV of total drop, short and reverse polarity protected
Power Good (PG)	Yes
Automatic On/Off Fan Control:	Yes, dependent on internal temperature, with hysteresis
Main output voltage adjustment:	Yes, ± 10% adjustment range via trimmer potentiometer (special option)

Fusing:	Dual, high-breaking-capacity fuses compliant to IEC60601-1, ≥1,500A breaking capacity
Over-Voltage Protection:	110 - 130%. Latched-off, cycle AC to reset
Over-Current Protection:	115% typical, CC operation when Vout is between 75 - 100% of nominal value, auto-recovery hiccup-mode when Vout collapses to <75% of nominal value
Short Circuit Protection:	Auto-recovery
Over-Temperature Protection:	Latched-off, cycle AC to reset
AC Under-Voltage Protection:	Brown-out trip @ 70Vac (nom.), Restore @ 75 - 80Vac

Operating Temperature:	-20°C to 50°C (full output power), -20°C to 70°C (linearly derated to 50% power rating @ 70°C)
Storage Temperature:	-30°C to 85°C
Humidity:	0% to 95% relative humidity, non-condensing
Altitude:	5000m max.
Vibration:	Conforms to EN60068-2-6, ISO80601-2, EN1789

Certifications:	IEC60601-1 IEC62368-1 IEC60335-1
Dielectric Withstand Voltage:	4000VAC or 5656VDC, primary-to-secondary 3000VAC or 4242VDC, primary-to-earth 3000Vac or 4242VDC, secondary-to-earth (Class II FE models only, N/A for Class I)
Suitable Medical Applications:	Type-B (Class I) or Type-BF (Class II with FE)
Output Touch Current:	NC: <80µA, SFC: <400µA (open neutral, open earth)
Earth Leakage Current	NC: <300µA, SFC: <1.0mA (open neutral)
Means of Protection:	2 x MOPP (primary-to-secondary), 1xMOPP (primary-to-earth), 1xMOPP (secondary-to-earth, Class II FE models only)

Certifications:	IEC60601-1-2 EN55032 (CISPR32) EN55035 (CISPR35)
Conducted Emissions:	Class B, FCC Part 15, Class B (with resistive load, Class I and Class II FE configurations)
Radiated Emissions:	Class B, FCC Part 15, Class B (with resistive load, Class I and Class II FE configurations)
Harmonic Current Voltage Distortion:	EN61000-3-2, Class A
Voltage Fluctuations/Flicker:	EN61000-3-3
Electrostatic Discharge (ESD) Immunity:	EN61000-4-2, 10KV contact discharge, 18KV air discharge (applied to output terminals, and to horizontal/vertical coupling planes [HCP/VCP] with power supply sitting on HCP)
Radiated RF Immunity:	EN61000-4-3, 20V/m 80-2700MHz, 80% 1KHz AM, 80% 5Hz AM
EFT/Burst Immunity:	EN61000-4-4, 4KV/100kHz.
Line Surge Immunity:	EN61000-4-5, 2KV differential, 4KV common-mode
Conducted RF Immunity:	EN61000-4-6, 3VRMS, 80% 1KHz AM
Power Frequency Magnetic Field Immunity:	EN61000-4-8, 30A/m
Voltage Dip Immunity:	EN61000-4-11

Dimensions:	U-Frame version: 6.00" x 4.00" x 1.69" (152.3mm x 101.6mm x 43.0mm) Enclosed version with top-side fan: 6.00" x 4.00" x 2.40" (152.3mm x 101.6mm x 61.0mm)
Fan Audible Noise Specification:	28.5dB(A) (Enclosed version with fan only)

Input Connector (J1):	Connector on PCB: TE Connectivity/AMP 641966-1 Recommended mate: TE Connectivity/AMP 350766-1 Pinout: 1: Neutral \| 2: Not used \| 3: Line
Main Output Connectors (J2, J3):	Connector on PCB: CNNT ACTB207 (M5 ring terminal), Recommended mounting torque: 2.0Nm Recommended mate: Various, depends on required wire size Pinout: J2: V+ \| J3: V- (GND)
Standby/Control Output Connector (J4):	Connector on PCB: Molex 0705550005 Recommended mate: Molex 0014562062 Pinout: 1: SNS+ \| 2: SNS- \| 3: PGOOD \| 4. EN \| 5. GND \| 6. +5VSB
Fan Output Connector: (J5):	Connector on PCB: Molex 22-04-1021 Recommended mate: Molex 22-01-1022 Pinout:1: GND \| 2: +FAN
Earth Connector (J6):	Connector on PCB: Kang Yang PCH250 (0.250" x 0.031" Faston) Recommended mate: TE Connectivity/AMP 2-520184-2

Derating Curve

Qty (ea.)/Carton

Individual Box/Gift Box Size (mm)

Individual Box/Gift Box Color

Master Carton Size (mm)

TBD

Gross Weight (kg)

Label Width (mm)

TBD

Label Height (mm)

TBD

Input Configuration

Description

null