Preferred ratings shown below. Custom output voltages available in 0.1V increment from the minimum voltage listed to the maximum voltage listed; contact sales.
Model Number (Final ordering #/Part No to be defined)
Voltage (V)
Current (A)
Power (W)
RFQ
GTM961800P18024-T3*
24
7.5
180
GTM961800P18019-T3*
19
9.47
179.93
GTM961800P18054-T3*
54
3.333
179.98
GTM961800P17024-T3*
24
7.08
169.92
GTM961800P18036-T3*
36
5
180
GTM961800P16012-T3*
12
13.33
159.96
GTM961800P17018-T3*
18
9.44
169.92
GTM961800P18020-T3*
20
9
180
GTM961800P18040-T3*
40
4.5
180
GTM961800P10812-T3*
12
9
108
GTM961800P16012-T3-CF*
12.0
13.33
159.96
GTM961800P18028-T3*
28
6.42
179.76
GTM961800P16012-T3-CF*
12
13.33
159.96
GTM961800P17015-T3-CF*
15
11.33
169.95
GTM961800P17018-T3-CF*
18
9.44
169.92
GTM961800P18019-T3-CF*
19
9.47
179.93
GTM961800P18020-T3-CF*
20
9
180
GTM961800P18024-T3-CF*
24
7.5
180
GTM961800P18028-T3-CF*
28
6.42
179.76
GTM961800P18030-T3-CF*
30
6
180
GTM961800P18036-T3-CF*
36
5
180
GTM961800P18048-T3-CF*
48
3.75
180
GTM961800P18054-T3-CF*
54
3.333
179.98
GTM961800P16018-T3-CF*
18
8.888
159.98
GTM961800P16013.5-T3*
13.5
11.85
159.98
GTM961800P15030-T3*
30
5
150
GTM961800P12012-T3*
12
10
120
GTM961800P17016.5-T3*
16.5
10.300
169.95
GTM961800P18030-T3*
30
6
180
GTM961800P17015-T3*
15
11.33
169.95
GTM961800P16018-T3*
18
8.888
159.98
GTM961800P18048-T3*
48
3.75
180
GTM961800PWWWVV.V-T3-XXXX
CUSTOM
CUSTOM
CUSTOM
* (Final ordering #/Part No to be defined)
Specifications
Input
Input Voltage:
Specified: 90-264VAC, Nameplate: 100-240VAC 100% rated load current for 90-264VAC 90% rated load current for 85-264VAC
Input Frequency:
Specified: 47-63Hz, Nameplate: 50-60Hz
Power Factor:
0.90 (min.) @ 230VAC, 0.97 (min.) @ 115VAC
No Load Input Power:
<150mW @ 230VAC (EU CoC Tier 2 compliant)
Inrush Current:
30A/60A max. (cold start @ 115V/230VAC)
Efficiency:
DoE Level VI and EU CoC Tier 2 compliant
Output
Turn-on Delay:
1 second typ. @ 115VAC and full load
Output Regulation:
± 4% (measured at output connector)
Line Regulation:
± 0.5% typ. (measured at output connector, full load)
Ripple:
1% or 200mV, whichever is greater (using a 47µF low-ESR cap + 0.1µF ceramic capacitor, measured @ 20MHz BW, at output connector)
Turn-On Overshoot:
5% max.
Transient Response:
5% max. deviation, 1ms recovery time (with 25% to 50% load step)
Hold-up Time:
20ms min.
Switching Frequency:
25 - 125KHz, depending on model and load condition
Power Indicator:
Green LED
Protections
Input Protection:
MOV transient suppressor, dual input line fusing
Over-Current Protection:
105 - 140% of rated output current, auto-restart
Short-Circuit Protection:
Auto-restart
Over-Voltage Protection:
110 - 135% (60V max. for output voltage ≥ 45V), latched off, cycle AC to reset
Complies with EU 2011/65/EU and China SJ/T 11363-2006
Note 1:
Regarding operating temperature a. See below de-rating table for output power capability at alternate temperature b. Extended low-end temperature range available as a custom option
Safety
Dielectric Withstand Voltage:
4000VAC or 5656VDC from input to output 3000VAC or 4242VDC from input to earth (Class I models only)
Touch Current:
Standard models (No suffix): Class I: 20µA max. Class II: 70µA max. Class II with Functional Earth (F2): 20µA max.
Low-leakage models (-CF suffix): Class II with Functional Earth (F2): 10µA max.
Note 2:
Standard models are designed for use in Type-B/BF medical applications. Low-leakage models are designed for use in Type-CF medical applications. (See IEC60601-1, Clause 16.6.1)
Earth Leakage Current
Class I: 300µA max. Class II: N/A
Means of Protection:
2 x MOPP
Output Isolation Options:
Class I: C6 or C14 inlet (output negative tied to Earth contact) Class II: C8 or C18 inlet Class II FE: C6 or C14 inlet (output isolated from Earth contact) Review isolation options by reading our white paper PSU Isolation and Identity.
Earth Continuity Test:
< 0.1Ω between earth pin (on AC inlet) and PCB termination point (Class I models only)
Compliant Standards:
See listing at end of this datasheet for specific standards
Class B, FCC Part 15, Class B (with resistive load)
Radiated Emissions:
Class B, FCC Part 15, Class B (with resistive load)
Harmonic Current Voltage Distortion:
EN61000-3-2, Class A
Voltage Fluctuations/Flicker:
EN61000-3-3
Electrostatic Discharge (ESD) Immunity:
EN61000-4-2, 10KV contact discharge, 18KV air discharge
Radiated RF Immunity:
EN61000-4-3, 10V/m 80-2700MHz, 80% 1KHz AM
EFT/Burst Immunity:
EN61000-4-4, 4KV/100kHz.
Line Surge Immunity:
EN61000-4-5, 2KV differential, 4KV common-mode
Conducted RF Immunity:
EN61000-4-6, 3VRMS, 80% 1KHz AM
Power Frequency Magnetic Field Immunity:
EN61000-4-8, 3A/m
Voltage Dip Immunity:
EN61000-4-11
Enclosure
Material/Construction:
High impact plastic, 94V0 polycarbonate, non-vented
Size:
176.5 * 74.0 * 40.0mm (±1.0mm)
AC Input Mechanical Options:
Desktop: C6, C7, C14, or C18 inlet
Markings:
Label and/or pad printed and/or laser-etched into case
Special Options
Custom cordsets, cord types, and connector types
Custom markings
Custom housing and cordset colors
Constant current/constant voltage (CC/CV) output behavior, with compliance voltage between (75% * Vout) and (100% * Vout)
Short term output surge power capability, for motor applications and short term intermittent high power applications. (Up to 300W for 1 second.)
IEC61000-3-2 Class C line harmonics for LED lighting applications
"Back EMF" upgrade, for motor loads and other high inductance applications with reverse energy flow requirements
Reduced touch/leakage current for IEC60601-1 Type-CF applications. (Available in models with -CF suffix.)
High reliability PCB laminate with plated through-holes for IPC610 Class 2 compliance
Tightened output voltage tolerance
Reduced output ripple level
Reduced output power rating
Improved ingress protection (IP) rating
Output Connectors
Several output connector options are available with various output current ratings. GlobTek can supply 10A rated 2.1mm and 2.5mm style DC Power Jacks, to complement our 10A output rated 2.1mm and 2.5mm DC power plugs used on our output cordsets.
Below are standard cordsets which are "not included" (unless stated above); these can be purchased separately or packaged with the power supply. Contact your Sales Engineer if the style required is not shown below. Many more available in different lengths, colors or cable material.
Contact GlobTek for your specific requirements or custom solutions.
Approvals
Below follows a link to the latest regulatory certifications and marks for this specific product. National standards as well as certification schemes are constantly changing and so is the set of certification marks and symbols applicable to this product. Various standards, marks and symbols, and certificates are subject to change at any time without notice.
Additional standards or unique country certifications are available upon request. Please contact Globtek to request a quotation.
Logo
Description
Medical 4th Ed.
EN/IEC 60601-1-2, 4th Edition (Please visit EMC reports for further info)
Audio/Video, Information And Communication Technology Equipment - Part 1: Safety Requirements [UL 62368-1:2014 Ed.2] Audio/Video, Information And Communication Technology Equipment - Part 1: Safety Requirements [CSA C22.2#62368-1:2014 Ed.2]
INDIA BIS (GTM961800P-T3) 12,13.5,15,18,19,24,30,36,48 and 54V only
PRECAUCION: PARA USO EN EQUIPOS ELECTRONICOS SOLAMENTE
IRAM certificate DC-E-G71-007.1 to IEC 62368-1:2014
No Logo
Greenhouse and Energy Minimum Standards (GEMS) for model GTM96180-1817.9-5.9
Compliance of this power supply with FCC Part 15, Class B has been demonstrated with a standard output load. The FCC law stipulates that system-level testing is required to demonstrate compliance with the FCC emission limits with the actual system load.
NOM MEXICO NYCE for GTM961800P16012-T3 (12V only)
Conforms to UL STD. 62368-1 Certified to CSA STD C22.2 NO.62368-1
Conforms to UL STD. 62368-1 Certified to CSA STD C22.2 NO.62368-1
Singapore to IEC 62368 (for 12V only)
Korea for GTM961800P16012-T3(A) (12-13.5V)
Taiwan BSMI GTM961200P-T3(A) R37924 GTM961800P16012-T3(A) ; 12,15,18,19,24,48 and 54V (does not apply to -CF models) http://www.bsmi.gov.tw/wSite/ct?xItem=4072&ctNode=816&mp=2
No Logo Applicable
CB for 60335-1:2010/COR1:2010/COR2:2010 /AMD1:2013/COR1:2014/AMD2:2016/COR1:2016
Hong Kong Safety Mark License IEC62368-1:2018
Saudi Arabia approval for GTM961800P16012-T3 and GTM961600P16024-T3GTM961800P-T3 IEC 60950-2005
No Logo Applicable
IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013
Indoor Use Only - Mark is on the label or Molded in the case
No Logo
Greenhouse and Energy Minimum Standards (GEMS) for model GTM961800P16012-T3(A) GTM961600P16012-T3(A)
RoHS
Specifications of directive 2011/65/EU Annex VI (ROHS-2) with amendment 2015/863-EU (ROHS-3) http://www.ce-mark.com/Rohs%20final.pdf
CHINA SJ/T 11364-2014, China RoHS Chart: http://www.globtek.com/pdf/F-GT-DJD-8.4.1-006%20China%20RoHS%20Declaration%205-20-22.pdf
CE Certification
Declaration ДС № ЕАЭС N RU Д-US.КА01.В.10453_19 Custom Union of Russia, Belarus and Kazakhstan http://www.globtek.com/redirect/?loc=gost-certificate-eac-declaration
JAPAN TUV R-PSE, Cert. No. JD 50469658, to J62368-1(H30) , J55032(H29),J3000(H25)[15V or less]. Please reference the following website for guidelines on PSE regulations: https://www.globtek.com/r2/Szj4Vb
Japan: Voluntary Control Council for Interference (VCCI)
Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
WEEE: Complies with EU 2012/19/EU (http://ec.europa.eu/environment/waste/weee/index_en.htm) Mark is on the label or Molded in the case
SAA-200456-EA
RCM certificate SAA-200456-EA; Australia and New Zealand Regulatory Compliance, Mark (http://rcm.standards.org.au/rcmfaq/rcmfaq.htm)
EN 60601-1:2006 + A1:2013 + A12:2014 EN 60601-1-11:2015
Conforms to AAMI STD.ES60601-1,IEC 60601-1-11 Certified to CAN/CSA STD.C22.2 NO.60601-1
Conforms to AAMI STD.ES60601-1,IEC 60601-1-11 Certified to CAN/CSA STD.C22.2 NO.60601-1
cETLus-Cert-60950-1 4007497 Listed
cETLus-Cert-4007497 ANSI/AAMI ES60601-1:2005 with AMD C1: 2009, AMD C2: 2010 and CAN/CSA-C22.2 No. 60601-1 2008 with COR 2:2011+ANSI/AAMI HA60601-1-11 Ed:1
IP41
Ingress Protection: ?IP41 to IEC60529:2001 Protection against granular foreign bodies - Protected against vertically falling drops of water
Conforms to UL STD. 60950-1 Certified to CSA STD C22.2 NO.60950-1
Conforms to UL STD. 60950-1 Certified to CSA STD C22.2 NO.60950-1
Korea KET KC Mark GTM961800P18024-T3 HU10499-21049A (24-30V)
CCC Altitude up to 5000 m GB17625.1-2012, GB4943.1-2011, GB/T9254-2008